View HS2-3530RH-Q_1251114.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HS-3530RH
August 1995
Low Power, Radiation Hardened Programmable Operational Amplifier
Pinout
8 LEAD METAL CAN PACKAGE (CAN) MIL-STD-1835 MACY1-X8 TOP VIEW
ISET 8 OFFSET NULL INVERTING INPUT 2 1 7 V+
Features
* Radiation Environment - Neutron Fluence () 5 x 1012 n/cm2 (E 10KeV) - Gamma Rate () 1 x 109 RAD (Si)/s - Gamma Dose () 1 x 106 RAD (Si) * Wide Range AC Programming - Slew Rate 0.06 to 3V/s - Gain X Bandwidth 100kHz to 5.0MHz * Wide Range DC Programming - Power Supply Range 3.0V to 15V * Supply Current 10A to 1.2mA * Dielectrically Isolated Device Islands * Short Circuit Protection
6
OUTPUT
NON-INVERTING INPUT
3 4 V-
5
OFFSET NULL
NOTE: 1. Case tied to V-.
Description
The HS-3530RH is a Low Power Operational Amplifier which is an internally compensated monolithic device offering a wide range of performance specifications. Parameters such as power dissipation, slew rate, bandwidth, noise and input DC parameters are programmed by selecting an external resistor or current source. Supply voltages as low as 3V may be used with little degradation of AC performance. The HS-3530RH has been specifically designed to meet exposure to space radiation environments. Operation from -55oC to +125oC is guaranteed. A major advantage of the HS-3530RH is that operating characteristics remain virtually constant over a wide supply range (3V to 15V), allowing the amplifier to offer maximum performance in almost any system, including battery operated equipment. A primary application for this device is in active filtering and conditioning for a wide variety of signals that differ in frequency and amplitude. Also, by modulating the set current, it can be used for designs such as current controlled oscillators/modulators, sample and hold circuits and variable active filters.
Functional Diagram
+V OFFSET NULL 2 7 -IN +IN 2 3 1 4 ISET -V OFFSET NULL 1 5 6 8 OUT
Ordering Information
PART NUMBER HS2-3530RH-8 HS2-3530RH-Q HS2-3530RH/SAMPLE TEMPERATURE RANGE -55oC to +125oC -55oC to +125oC +25oC PACKAGE 8 Lead Metal Can 8 Lead Metal Can 8 Lead Metal Can DB NA
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright (c) Intersil Corporation 1999
Spec Number File Number
762
518079 3024.2
Specifications HS-3530RH
Absolute Maximum Ratings
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VISET (Current at ISET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500A VSET (Voltage to GND at ISET). . . . . . . . . (V+ -2.0V) < VSET < V+ Output Short Circuit Duration (Note 1) . . . . . . . . . . . . . . . . Indefinite Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . . 275oC
Reliability Information
Thermal Resistance JA JC Metal Can Package . . . . . . . . . . . . . . . . . 160oC/W 70oC/W Maximum Package Power Dissipation at +125oC Ambient: Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.31W If device power exceeds package dissipation capability, provide heat sinking or derate linearly at the following rate: Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3mW/oC
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 15V VINcm 1/2 (V+ - V-) RL 2kV
TABLE 1A. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: Supply Voltage = 15V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUP 1 2, 3 +IB VCM = 0V, +RS = 10k -RS = 100 Note 2 1 2, 3 3 -IB VCM = 0V, +RS = 100 -RS = 10k Note 2 1 2, 3 3 Input Offset Current IIO VCM = 0V, +RS = 10k -RS = 10k Note 2 1 2, 3 3 Large Signal Voltage Gain +AVOL VOUT = 0V and +10V Note 1 VOUT = 0V and -10V Note 1 VCM = +5V, +V = +10V -V = -20V, VOUT = -5V VCM = -5V, +V = +20V -V = -10V, VOUT = +5V Note 1 4 5, 6 4 5, 6 1 2, 3 1 2, 3 1 2, 3 -VOUT Note 1 1 2, 3 Output Current +IOUT -IOUT RL = 2k RL = 2k 1 1 ISET = 1.5A TEMPERATURE +25oC +125oC, -55oC MIN -3 -5 65 25 65 25 80 80 80 80 12.5 10.5 0.25 MAX 3 5 -12.5 -10.5 -0.25 ISET = 15A MIN -3 -5 -40 -50 -60 -40 -50 -60 -15 -20 -30 80 50 80 50 80 80 80 80 12.5 10.5 2.5 MAX 3 5 40 +50 60 40 +50 60 15 +20 30 -12.5 -10.5 -2.5 UNITS mV mV nA nA nA nA nA nA nA nA nA kV/V kV/V kV/V kV/V dB dB dB dB V V V V mA mA
PARAMETER Input Offset Voltage Input Bias Current
SYMBOL VIO
CONDITIONS VCM = 0V
+25oC +125oC, 0oC
-55oC +25oC +125oC, 0oC
-55oC +25oC +125oC, 0oC
-55oC +25oC +125oC, -55oC
-AVOL
+25oC +125oC, -55oC
Common Mode Rejection Ratio
+CMRR
+25oC +125oC, -55oC
-CMRR
+25oC +125oC, -55oC +25oC +125oC, -55oC
Output Voltage Swing
+VOUT
+25oC +125oC, -55oC
+25oC +25oC
Spec Number 763
518079
Specifications HS-3530RH
TABLE 1A. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: Supply Voltage = 15V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUP 1 2, 3 -ICC IOUT = 0mA 1 2, 3 Power Supply Rejection Ratio +PSRR VSUP = 10V +V = +10V, -V = -15V +V = +20V, -V = -15V VSUP = 10V +V = +15V, -V = -10V +V = +15V, -V = -20V 1 2, 3 1 2, 3 ISET = 1.5A TEMPERATURE +25oC +125oC, -55oC MIN -15 -15 80 80 80 80 MAX 15 15 ISET = 15A MIN -150 -160 80 80 80 80 MAX 150 160 UNITS A A A A dB dB dB dB
PARAMETER Quiescent Power Supply Current
SYMBOL +ICC
CONDITIONS IOUT = 0mA
+25oC +125oC, -55oC
+25oC +125oC, -55oC +25oC +125oC, -55oC
-PSRR
NOTES: 1. RL = 75k at ISET = 1.5A, RL = 5k at ISET = 15A. 2. Temperature 0oC performed for Intersil -8 product flow only. TABLE 1B. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: Supply Voltage = 3V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUP 1 2, 3 +AVOL VOUT = 0V and +1V Note 1 VOUT = 0V and -1V Note 1 VCM = +1.5V +V = +1.5V, -V = -4.5V VOUT = -1.5V VCM = -1.5V +V = +4.5V, -V = -1.5V VOUT = +1.5V Note 1 4 5, 6 4 5, 6 1 2, 3 1 2, 3 1 2, 3 -VOUT Note 1 1 2, 3 Quiescent Power Supply Current +ICC IOUT = 0mA 1 2, 3 -ICC IOUT = 0mA 1 2, 3 Power Supply Rejection Ratio +PSRR VSUP = 1.5V +V = +3V, -V = -3V +V = +4.5V, -V = -3V VSUP = 1.5V +V = +3V, -V = -3V +V = +3V, -V = -4.5V 1 2, 3 1 2, 3 ISET = 1.5A TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC MIN -3 -5 25 15 25 15 80 80 80 80 2.0 2.0 -15 -15 80 80 80 80 MAX 3 5 -2.0 -2.0 15 15 ISET = 15A MIN -3 -5 25 25 25 25 80 80 80 80 2.0 2.0 -150 -160 80 80 80 80 MAX 3 5 -2.0 -2.0 150 160 UNITS mV mV kV/V kV/V kV/V kV/V dB dB dB dB V V V V A A A A dB dB dB dB
PARAMETER Input Offset Voltage Large Signal Voltage Gain
SYMBOL VIO
CONDITIONS VCM = 0V
-AVOL
+25oC +125oC, -55oC +25oC +125oC, -55oC
Common Mode Rejection Ratio
+CMRR
-CMRR
+25oC +125oC, -55oC
Output Voltage Swing
+VOUT
+25oC +125oC, -55oC +25oC +125oC, -55oC
+25oC +125oC, -55oC +25oC +125oC, -55oC
+25oC +125oC, -55oC +25oC +125oC, -55oC
-PSRR
NOTE: 1. RL = 75k at ISET = 1.5A, RL = 5k at ISET = 15A.
Spec Number 764
518079
Specifications HS-3530RH
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: CL = 100pF, AVCL = +1, RL = 75k, Unless Otherwise Specified. GROUP A SUBGROUP ISET = 1.5A TEMPERATURE MIN MAX ISET = 15A MIN MAX UNITS
PARAMETER VSUPPLY = 15V Slew Rate Note 1
SYMBOL
CONDITIONS
+SR -SR
VOUT = -10V to +10V VOUT = +10V to -10V VOUT = 0 to +400mV 10% < TR < 90% VOUT = 0 to -400mV 10% < TF < 90% VOUT = 0 to +400mV VOUT = 0 to -400mV
9 9 9 9 9 9
+25oC +25oC +25oC +25oC +25oC +25oC
0.025 0.025 -
8.0 8.0 35 35
0.25 0.25 -
0.8 0.8 35 35
V/s V/s s s % %
Rise & Fall Time TR TF Overshoot +OS -OS VSUPPLY = 3V Slew Rate Note 1 +SR -SR
VOUT = -2V to +2V VOUT = +2V to -2V
9 9
+25oC +25oC
0.01 0.01
-
0.1 0.1
-
V/s V/s
TABLE 3. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: RSOURCE = 50, CL = 100pF, AVCL = +1, Unless Otherwise Specified. ISET = 1.5A PARAMETER VSUPPLY = 15V Differential Input Resistance Full Power Bandwidth Minimum Closed Loop Stable Gain Output Resistance Quiescent Power Consumption Output Short-Circuit Current Gain Bandwidth Product VSUPPLY = 3V Gain Bandwidth Product NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2VPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs). 4. Caution: Continuous long-duration short-circuit operation may degrade the operating life of the device. GBWP AVCL = 10V/V VO = 200mV, fO = 10kHz 1 +25oC 30 600 kHz RIN FPBW CLSG ROUT PC IOSC GBWP VCM = 0V VPEAK = 10V RL = 2k, CL = 50pF Open Loop VOUT = 0V, IOUT = 0mA VOUT = 0V AVCL = 10V/V VO = 200mV, fO = 10kHz 1 1, 2 1 1 1, 3 1, 4 1 +25oC +25oC -55oC to +125oC +25oC -55oC to +125oC 50 0.4 +1 -14 45 10 4.8 38 50 4 +1 -27 750 10 4.8 42 M kHz V/V mW mA kHz SYMBOL CONDITIONS NOTES TEMPERATURE MIN MAX ISET = 15A MIN MAX UNITS
+25oC +25oC
Spec Number 765
518079
Specifications HS-3530RH
TABLE 4. POST RAD DC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER Open Loop Voltage Gain Input Offset Voltage SYMBOL AVOL VIO CONDITIONS VSUPPLY = 15V ISET = 15A VSUPPLY = 15V ISET = 15A TEMPERATURE +25oC +25oC MIN 15 MAX 5.0 UNITS kV/V mV
TABLE 5. BURN-IN DELTA PARAMETERS GROUP B, SUBGROUPS 5 (TA = +25oC) PARAMETER VIO IBIAS DELTA LIMIT 0.5mV 30nA
TABLE 6. APPLICABLE SUBGROUPS GROUP A SUBGROUPS CONFORMANCE GROUP Initial Test Interim Test PDA Final Test Group A (Note 1) Subgroup B5 Subgroup B6 Group C Group D Group E, Subgroup 2 NOTES: 1. Alternate Group A testing in accordance with MIL-STD-883 method 5005 may be exercised. 2. Table 5 parameters only MIL-STD-883 METHOD 100% 5004 100% 5004 100% 5004 100% 5004 Sample 5005 Sample 5005 Sample 5005 Sample 5005 Sample 5005 Sample 5005 RECORDED FOR -Q 1 (Note 2) 1, (Note 2) 1, 2, 3, (Note 2) RECORDED FOR -8
TESTED FOR -Q 1, 4, 9 1, 4, 9, 1, 2, 3, 5, 6 1, 2, 3, 4, 5, 6, 9 1, 2, 3, 4, 5, 6, 9, 1, 4, 9 1, 4, 9 1
TESTED FOR -8 1, 4, 9 1, 4, 9 1 2, 3, 5, 6 1, 2, 3, 4, 5, 6, 9 1, 2, 3, 4, 5, 6, 9 1, 4, 9 1
Spec Number 766
518079
HS-3530RH Intersil Space Level Product Flow -Q
Wafer Lot Acceptance (All Lots) Method 5007 (Includes SEM) GAMMA Radiation Verification (Each Wafer) Method 1019, 4 Samples/Wafer, 0 Rejects 100% Nondestructive Bond Pull, Method 2023 Sample - Wire Bond Pull Monitor, Method 2011 Sample - Die Shear Monitor, Method 2019 or 2027 100% Internal Visual Inspection, Method 2010, Condition A 100% Temperature Cycle, Method 1010, Condition C, 10 Cycles 100% Constant Acceleration, Method 2001, Condition per Method 5004 100% PIND, Method 2020, Condition A 100% External Visual 100% Serialization
NOTES: 1. Failures from subgroup 1 and deltas are used for calculating PDA. The maximum allowable PDA = 5%. 2. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004. 3. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005. 4. Group B and D inspections are optional and will not be performed unless required by the P.O. When required, the P.O. should include separate line items for Group B test, Group B samples, Group D test and Group D samples. 5. Group D Generic Data, as defined by MIL-I-38535, is optional and will not be supplied unless required by the P.O. When required, the P.O. should include a separate line item for Group D generic data. Generic data is not guaranteed to be available and is therefore not available in all cases. 6. Data Package Contents: * Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number, Quantity). * Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage. * GAMMA Radiation Report. Contains Cover page, disposition, RAD Dose, Lot Number, Test Package used, Specification Numbers, Test equipment, etc. Radiation Read and Record data on file at Intersil. * X-Ray report and film. Includes penetrometer measurements. * Screening, Electrical, and Group A attributes (Screening attributes begin after package seal). * Lot Serial Number Sheet (Good units serial number and lot number). * Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test. * Group B and D attributes and/or Generic data is included when required by the P.O. * The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed by an authorized Quality Representative.
100% Initial Electrical Test (T0) 100% Static Burn-In, Condition A or B, 240 Hours, +125oC or Equivalent, Method 1015 100% Interim Electrical Test 1 (T1) 100% Delta Calculation (T0-T1) 100% PDA, Method 5004 (Note 1) 100% Final Electrical Test 100% Fine/Gross Leak, Method 1014 100% Radiographic (X-Ray), Method 2012 (Note 2) 100% External Visual, Method 2009 Sample - Group A, Method 5005 (Note 3) Sample - Group B, Method 5005 (Note 4) Sample - Group D, Method 5005 (Notes 4 and 5) 100% Data Package Generation (Note 6)
Spec Number 767
518079
HS-3530RH Intersil Space Level Product Flow -8
GAMMA Radiation Verification (Each Wafer) Method 1019, 4 Samples/Wafer, 0 Rejects Periodic- Wire Bond Pull Monitor, Method 2011 Periodic- Die Shear Monitor, Method 2019 or 2027 100% Internal Visual Inspection, Method 2010, Condition B 100% Temperature Cycle, Method 1010, Condition C, 10 Cycles 100% Constant Acceleration, Method 2001, Condition per Method 5004 100% External Visual 100% Initial Electrical Test 100% Static Burn-In, Condition A or B, 160 Hours, +125oC or Equivalent, Method 1015 100% Interim Electrical Test 100% PDA, Method 5004 (Note 1) 100% Final Electrical Test 100% Fine/Gross Leak, Method 1014 100% External Visual, Method 2009 Sample - Group A, Method 5005 (Note 2) Sample - Group B, Method 5005 (Note 3) Sample - Group C, Method 5005 (Notes 3 and 4) Sample - Group D, Method 5005 (Notes 3 and 4) 100% Data Package Generation (Note 4)
NOTES: 1. Failures from subgroup 1 are used for calculating PDA. The maximum allowable PDA = 5%. 2. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005. 3. Group B, C and D inspections are optional and will not be performed unless required by the P.O. When required, the P.O. should include separate line items for Group B test, Group B samples, Group C test and Group C samples and Group D test and Group D samples. 4. Group C and/or D Generic Data, as defined by MIL-I-38535, is optional and will not be supplied unless required by the P.O. When required, the P.O. should include a separate line item for Group C generic data and/or D generic data. Generic data is not guaranteed to be available and is therefore not available in all cases. 5. Data Package Contents: * Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number, Quantity). * GAMMA Radiation Report. Contains Cover page, disposition, RAD Dose, Lot Number, Test Package used, Specification Numbers, Test equipment, etc. Radiation Read and Record data on file at Intersil. * Screening, Electrical, and Group A attributes (Screening attributes begin after package seal). * Group B, C and D attributes and/or Generic data is included when required by the P.O. * The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed by an authorized Quality Representative.
Spec Number 768
518079
HS-3530RH Test Circuit
ACOUT +VCC 2K 10K 0.1 1 500K S1 1 OPEN 2 S2 1 OPEN 2 2 10K VAC 100 100 5K 0.1 1 -VEE 2K 5K 75K x2 EOUT 1 2 S4 + 2 100pF FOR LOOP STABILITY, USE MIN VALUE CAPACITOR TO PREVENT OSCILLATION -1 V1
500K OPEN 1 2 3 4 S8 2 V2 + 1 + FB
DUT
1 S5
S9 1 1
S7
2 1
S3
50K
Includes Stray Capacitance All Resistors = 1% () All Capacitors = 10% (F)
Simplified Transient Response/Slew Rate Circuit
2 3 + 8 100pF VINN RSET RL 6 VOUT
-V
Burn-In Circuit
+V
Irradiation Circuit
+15V 7 2 +V OUTPUT 3 + 8 R1 4 0.01F -V C2 D2 -15V R2 3 ISET 6 2 + 4 6 0.01F 8 7 C1 D1 1M
Spec Number 769
518079
HS-3530RH Typical Performance Curves
100 1000 SUPPLY CURRENT (A) BIAS CURRENT (nA)
PRE-RAD
10
100 VSUPPLY = 15V VSUPPLY = 3V
VSUPPLY = 15V
1 1 10 SET CURRENT (A) 100
10 1 10 SET CURRENT (A) 100
FIGURE 1. INPUT BIAS CURRENT vs SET CURRENT
FIGURE 2. PRERAD POSITIVE SUPPLY CURRENT
200K GAIN-BANDWIDTH PRODUCT (MHz)
6 4
100K AVOL (V/V)
2 1 0.8 0.6 0.4
VSUPPLY = 15V VSUPPLY = 3V
0.2 0.1
10K
1
10 SET CURRENT (A)
100
1
10 SET CURRENT (A)
100
FIGURE 3. PRERAD LARGE SIGNAL VOLTAGE GAIN vs ISET
FIGURE 4. GAIN BANDWIDTH PRODUCT vs SET CURRENT
10
30 SLEW RATE (V/s) 1.0 25 20 VP-P SLEW RATE = 0.1 SR+ = SR2 ISET = 15A 15 10 PRE-RAD 5 0.01 1 10 100 SET CURRENT (A) VSUPPLY = 15V T = +25oC ISET = 1.5A
VSUPPLY = 15V VSUPPLY = 3V
1K
10K RLOAD ()
100K
1M
FIGURE 5. SLEW RATE vs SET CURRENT
FIGURE 6. OUTPUT VOLTAGE SWING vs LOAD RESISTANCE
Spec Number 770
518079
HS-3530RH Typical Performance Curves
25
(Continued)
200K VSUPPLY = 15V
20 BIAS CURRENT (nA) AVOL (V/V) ISET = 15A 15 PRE-RAD
100K
10
VSUPPLY = 3V
ISET = 15A ISET = 1.5A
5 VSUPPLY = 15V -50 -25 0 25 50 75 100 125 10K -50 -25 0 25 50 75 100 125 TEMPERATURE (oC)
TEMPERATURE (oC)
FIGURE 7. INPUT BIAS CURRENT vs TEMPERATURE
FIGURE 8. OPEN LOOP VOLTAGE GAIN vs TEMPERATURE
Schematic
VCC D2 Q23 Q1 Q39A Q39B Q25 Q31 2pF Q23 Q24 Q44 R1 20 Q37
20W
Q26 8 1 SET 2 INQ9 D13 D14 Q0 Q27 D47 D48 D49 D50 27pF Q28 Q11 Q12 Q19 Q20 R5 20 Q4 Q5 Q42 Q22
Q34
D32
R2 20 OUT 6 D43 R3 20
D33 D28 Q41 Q16 Q45 Q18 Q46
Q35 Q30
Q7
Q8 R7 3K R8 D17 3K
Q36 R4 20
D6
D15
D29
4 VEE
3 IN+
1 VOS1
5 VOS2
Spec Number 771
518079
HS-3530RH Metallization Topology
DIE DIMENSIONS: 54 x 67 x 11.5mils (1370 x 1700 x 290m) METALLIZATION: Type: Al Thickness: 12.5kA 2kA GLASSIVATION: Type: SiO2 Thickness: 8kA 1kA DIE ATTACH: Temperature: Metal Can - 420oC (Max) WORST CASE CURRENT DENSITY: 0.544 x 105 A/cm2 at 2.5mA SUBSTRATE POTENTIAL (POWERED UP): -V TRANSISTOR COUNT: 49 PROCESS: Complimentary Bipolar
Metallization Mask Layout
HS-3530RH OFFSET NULL
+IN
-IN
-V (& PACKAGE)
ISET
OFFSET NULL OUTPUT
+V
Spec Number 772
518079
HS-3530RH
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (407) 724-7000 FAX: (407) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029
Spec Number 773
518079

▲Up To Search▲

Price & Availability of HS2-3530RH-Q

	To Download HS2-3530RH-Q Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .